.. meta:: :scope: evolabel .. _tut_CPU_unit-index: ######## CPU Unit ######## .. _CPU_unit-backup: ============== Printer Backup ============== Backups contain system configuration, user data and log files. |br| Some of the information is stored in temporary memory and is lost at power off. When creating a backup it is important that the printer is kept power on between an issue happening and the backup. |br| ------------------------------------------- How to Store a Backup to a USB Memory Stick ------------------------------------------- 1. Log in to Service level (default 4113). 2. Insert the USB memory stick into one the the printer's USB ports. 3. Wait for the USB icon to be displayed to the left of the printer clock. 4. Navigate to :menuselection:`Settings --> System --> Backups --> Create Backup`. 5. Select the USB Drive. 6. Tap :menuselection:`Backup` to start the backup. .. image:: /media/tutorials/backup_to_USB.png :height: 200pt ----------------------------------------------- How to Restore a Backup from a USB Memory Stick ----------------------------------------------- 1. Log in to Service level (default 4113). 2. If the backup is on a USB memory stick, insert the USB memory stick into one the the printer's USB ports and wait for the USB icon to be displayed 3. Navigate to :menuselection:`Settings --> System --> Backups --> Restore From Backup` 4. Tap :menuselection:`Refresh Backups` 5. Unfold the menu "Select Backup to Restore" and select the backup to be restored. 6. Select at least one Component to restore a. Settings |br| Printer related settings. E.g. Printer model, applicator type b. Products, Layouts, and Layout Resources |br| Product lists, layouts, fonts images etc. c. Apps |br| Custom apps loaded to the printer d. Network Configuration |br| How printer IP is assigned, DNS settings etc. |br| Normally only used when replacing a CPU box. e. Licenses |br| Extra software licenses, e.g. printer High Speed mode. 7. Tap :menuselection:`Restore and Restart` .. image:: /media/tutorials/backup_restore_1.png :height: 186pt .. image:: /media/tutorials/backup_restore_2.png :height: 200pt See also `How to create a backup or restore a backup from printer user interface. `_ ================ Factory Defaults ================ Factory Default is a restore point that should be created when the system is setup and operates without any issue. Restore to the Factory Default during fault finding to put the system in a known good state. Before Factory Defaults can be stored, the printer serial number must be entered. The serial number must consist of the printer model plus the serial number on the machine sign, padded to six digits with leading zeroes. Example: T63-000335. See also `How to create Factory Defaults or restore to Factory Defaults from printer user interface. `_ ========================= Software Update ========================= See also `Software Update from the printer user interface. `_ -------------------------------- Printer with Internet Connection -------------------------------- When :menuselection:`Settings --> System --> Software Update --> Internet Update` is enabled, the system contacts Evolabel™ upgrade servers and adds them to the Available Updates list. Show Old Versions When enabled, all available versions are listed. By default only the latest version is displayed. Use Beta Software When enabled, version with experimental features are displayed. Available Updates When expanding this item, the system scans for available updates. .. image:: /media/tutorials/software_update_Internet.png :width: 500pt #. Log in to Service level (default 4113). #. Enable Internet Update. #. Select if Beta Software and Old Versions should be listed. #. Open "Available Updates" section. #. Select the update to be installed. #. Press Install Selected Software to start the installation. #. At the end of the installation you need to select if the software should be restarted or printer should be rebooted. It is a good practice to reboot the printer after a software change. -------------------------------- Offline Software Update -------------------------------- #. Log in to Service level (default 4113). #. Go to the `Firmware Change Log `_ to find the software version needed. |br| Use the download link to download the version. A .run file is downloaded. #. Copy the file to the root of a USB memory. #. Install the USB memory in printer. #. Wait for the USB icon to be displayed. #. Navigate to :menuselection:`Settings --> System --> Software Update`. #. Deselect Internet Update. #. Open "Available Updates" section. #. Select the update. #. Press Install Selected Software to start the installation. #. At the end of the installation you need to select if the software should be restarted or printer should be rebooted. It is a good practice to reboot the printer after a software change. #. Remove the USB memory. .. image:: /media/tutorials/software_update_offline.png :width: 500pt -------------------------------------------------- Upgrade and downgrade between software G1 and G2 -------------------------------------------------- * How do I upgrade from G1 to G2 software? * How do I reinstall a CPU Unit G3 Plus Edition system? * How do I downgrade to G1? See `Upgrade and downgrade between software G1 and G2. `_ ========================= How to Replace a CPU Unit ========================= When replacing a CPU unit, it’s extremely important that the printer is powered off. Always remove the power plug from the printer before starting to replace the CPU Unit. Removing a CPU Unit when the printer is powered on is likely to lead to irreparable (out of warranty) damages to the CPU Unit. It also exposes you to a live current. General Instructions 1. If the CPU unit to be replaced is still operational it is a good idea to take a :ref:`backup `. 2. Turn off the printer on the power switch 3. Remove the power cable from the printer 4. Remove the back and front covers 5. Remove all cabling from the CPU unit 6. Remove the CPU unit, See mounting details below 7. Install the new CPU unit 8. Reinstall all cabling from the CPU unit 9. Replace the back and front covers 10. Replace the printer power cable 11. Turn on the power switch to start the printer. ---------------- Mounting Details ---------------- CPU G3-SE and G3-PE ------------------- * To dock the CPU unit in the printer, align its position through the guiding pin and through the data bus connector. * Push in until it bottoms against the plate. |br| For printers delivered with the new Power supply (introduced 2020 Q4) a magnet aids to maintain the CPU unit in position until the two fixing screws are tightened. This will aid situations where the orientation of the printer align the CPU unit downwards. * Use a T25 torx (preferably with about 9cm long shaft) to tighten the two screws (b) that are reached from the back / rear side of the printer next to the power supply. .. image:: /media/tutorials/CPU_G3_mount.png :height: 150pt CPU G2 ------ 1. Take off the transport screw that pinches the shackle. 2. Take out shackle 3. Take out CPU unit .. image:: /media/tutorials/cpu_g2_mount.png :height: 150pt .. |br| raw:: html